Hand Tools - Pliers and Wire Cutters - Canadian Centre for …
WEBChoose pliers or wire cutters that have a grip span of 6 cm - 9 cm (2 1/2 - 3 1/2 in.) to prevent your palm or fingers from being pinched when the tools are closed. Use adjustable pliers that allow you to grip the workpiece firmly while maintaining a comfortable handgrip (i.e., hand grasp is not too wide). Use tools only if they are in good ...
WEBe wire back and forth against the cutting edges.Choose pliers or wire cutters that have a grip span of 6 cm - 9 cm (2 1/2 - 3 1/2 in.) to prevent your palm or fing. rs from being pinched when the tools are closed.Use adjustable pliers that allow you to grip the workpiece firmly while maintaining a comfort.
CCOHS: Powered Hand Tools - Electric Tools - Basic Safety
WEBMay 10, 2024 · Avoid body contact with grounded surfaces like refrigerators, pipes and radiators when using electric powered tools; this will reduce the likelihood of shock if the operator's body is grounded. Do not plug several power cords into one outlet by using single-to-multiple outlet adapters or converters ("cube taps"). Do not use light duty …
Hand Tools - Cutting Tools for Bolts, Cables, and Strapping
WEBMany types and sizes of cutters are used for cutting selected metal products made from iron, steel, or softer, non-ferrous materials (e.g., copper, brass, aluminum). Cutters are designed to cut materials of different kinds of products such as wires, cables (electrical, coax, multi-strand), wire ropes, fencing, bolts, rods, pre-stressed concrete ...
WEBpes, fencing, bolts, rods, pre-stressed concrete wires, and strapping.Wear safety glasses or goggles, or a face shield (with safety glas. es or goggles) and protective cut-res. stant gloves when using cutters.Choose the proper cutter for the job. Cu. ters are designed for a specific type, hardness, and size of material.Use a vi.
Hand Tools - Snips - Canadian Centre for Occupational Health and …
WEBOnly use snips that are sharp and in good condition. Wear safety glasses or goggles, or a face shield (with safety glasses or goggles) and protective gloves when working with snips. Small pieces of metal may go flying in the air and the cut edges of metal are sharp. Left cut snips are for making cuts to the left and straight cuts.
Tools and Machines - Canadian Centre for Occupational Health …
WEBMar 21, 2018 · POINT sharp tools laying on benches away from aisles, and handles should never extend over the edge of the bench top. MAINTAIN tools clean and dry, and store them properly after use. CARRY tools in a sturdy box to and from the worksite. WEAR safety glasses or goggles and well-fitting gloves appropriate for the hazards.
WEBplace worn jaws on wrenches, pipe tools and pliers.R. dress burred or mushroomed. eads of striking tools.Pull on a wrench or pliers. Neve. push unless you hold the tool with your palm open.Point sharp tools (e.g., saws, chisels, knives) laying on benches away from aisles, and handl. s should not extend over.
Hand Tools - Screwdrivers - Canadian Centre for Occupational …
WEBUse the correct screwdriver for the job. Always match the screwdriver to the screw head, both in terms of size and type. Choose contoured handles that fit the shank tightly, with a flange to keep the hand from slipping off the tool. Use a slot screwdriver with a blade tip width that is the same as the width of slotted screw head.
Hand Tools - Non-sparking tools - Canadian Centre for …
WEBUse local or mechanical ventilation systems as appropriate to remove hazardous materials, dusts, and vapours from the workplace. Non-sparking tools will need to be redressed more often. Follow normal safety procedures when sharpening non-sparking tools such as the provision of eye and face protection, adequate extraction and dust collection ...
Skip to content